Current position > Product detail
『Turbines Inc. Flow Meter Repairs Kit: Sourcing Legacy Replacement Parts』Related information(clamp on meter|electromagnetic meter|venturi meterrotameter|orifice meter|ultrasonic flow meter|mass flow meter|coriolis mass flow meter|coriolis flow meter|magnetic flow meter|magmeter flow meter|magflow flow meter|mag meter flow meter|electromagnetic flow meter|vortex flow meter|turbine flow meter|thermal mass flow meter|thermal flow meter|rotameter flow meter)
Turbines Inc. Flow Meter Repairs Kit: Sourcing Legacy Replacement Parts
Quick Answer: You can source replacement parts and repair kits for Turbines Inc. flow meters without replacing the whole meter. Silver Automation Instruments supplies rotors, shafts, bearings, pickups, O-rings, and preamps as legacy replacement parts for Turbines Inc. flow meters. Send us the model code, meter size from DN15 to DN300, fluid type, pressure in bar, and temperature in °C. We will return a firm quote with a lead time of 7 to 10 working days.
Why Legacy Turbine Meter Repairs Are Hard to Source
Many plants in Southeast Asia, Latin America, and the Middle East still run Turbines Inc. flow meters on fuel oil, chemical batching, and water lines. The original supplier may no longer hold inventory for older designs. Some local distributors only offer a full meter replacement. In practice, a failed bearing or a worn rotor does not need a new meter. The meter body can stay in the pipe.
We have seen this on customer sites many times. A water treatment plant in the Philippines had a DN100 turbine meter with a cracked pickup. The meter body was still in good condition. The local agent quoted 12 weeks for a new meter. We sourced a compatible pickup and preamp in 6 days. The total cost was far below a replacement meter.
What a Turbines Inc. Flow Meter Repair Kit Should Include
Each repair kit should match the wetted materials, bearing type, and signal output. Common parts include a rotor assembly, tungsten carbide or ceramic shaft, bearing set, O-rings, retaining rings, a magnetic pickup or RF pickup, and a preamplifier if the meter uses a low level signal.
For chemical and fuel applications we check compatibility before quoting. Here is the thing. Many older flow meters fail from bearing wear, not from a dead body. A paint manufacturer in Vietnam needed a rotor for a DN25 meter on solvent at 4 bar and 25 °C. The original rotor material was not available locally. We supplied a 316 stainless steel rotor with PTFE coated bearings. The meter went back into service within two weeks.
Matching Parts Without the Original Drawings
Most engineers skip this part because they assume the serial number is enough. In practice, the serial number helps but it does not always confirm the internals. We ask for the model tag, meter size, flow range, fluid, and signal output. If you have the old parts, send photos with a ruler beside the rotor and shaft. That removes most guesswork.
We can match DN15, DN25, DN40, DN50, DN80, DN100, DN150, DN200, and larger meters. We also handle special pickups for 4-20 mA HART output, pulse output, and ATEX Zone 1 installations. Some repair jobs include a PT100 sensor in the meter body for temperature compensation. We supply that as part of the kit when the orig
Lead Times and Fluid Data That Matter
Lead time depends on part complexity. Standard rotor and bearing kits for DN15 to DN100 meters usually ship in 7 to 10 working days. Larger DN150 to DN300 kits may take 15 working days because the rotor is machined to order. If the meter runs on viscous fluid such as heavy fuel oil at 380 cSt, the rotor clearance and bearing load change. Tell us the viscosity in cP or cSt when you send the inquiry.
For water service, we ask for conductivity in µS/cm if the meter signal is unstable. For gas and steam, we ask for flow rate in kg/h or m3/h at line conditions. These details help us select the right pickup type and preamp gain.
We have supplied Turbines Inc. replacement parts for diesel loading skids in Malaysia, seawater flow lines in Oman, and a food grade syrup batching line in Mexico. In each case the meter body remained in place. Only the internal kit was replaced. That saved downtime and avoided pipe spool changes.
FAQ: Turbines Inc. Flow Meter Repairs Kit
Can you supply parts for all Turbines Inc. models?
We cover common legacy turbine meter models from DN15 to DN300. Send us the model tag and photos of the internals. We will confirm compatibility before you order.
How long does delivery take?
Standard repair kits ship in 7 to 10 working days. Large rotors or special materials may take 15 working days. Express shipping to Southeast Asia, the Middle East, and Latin America usually adds 3 to 5 days.
Do you only supply parts or can you repair the meter?
We supply parts and provide remote guidance for reassembly. We can also receive the meter at our Nanjing facility if you need a full repair service.
Are your parts genuine Turbines Inc. parts?
We supply compatible aftermarket parts. Materials and dimensions follow the original meter design. We do not claim to be the original equipment manufacturer.
What information do you need for a quote?
Send the meter size in DN, flow range, fluid type, temperature in °C, pressure in bar, and output signal. If available, include photos of the rotor, shaft, and pickup.
Contact Silver Automation Instruments
Send us your Turbines Inc. flow meter model, pipe size in DN, flow range, fluid type, pressure in bar, and temperature in °C. We will quote the repair kit and freight cost. Contact Silver Automation Instruments by telephone at +86-25-68650347, WhatsApp at +86-25-52155837, or WeChat at +86 15365082610.
If the meter body is damaged or the process changed, we also supply Coriolis mass flow meters, electromagnetic flow meters, ultrasonic flow meters, oval gear flow meters, and thermal mass flow meters as replacement options.