What does T/HT mean in a water flow meter?

『Specification of water flow meter』Related information(clamp on meter|electromagnetic meter|venturi meterrotameter|orifice meter|ultrasonic flow meter|mass flow meter|coriolis mass flow meter|coriolis flow meter|magnetic flow meter|magmeter flow meter|magflow flow meter|mag meter flow meter|electromagnetic flow meter|vortex flow meter|turbine flow meter|thermal mass flow meter|thermal flow meter|rotameter flow meter)

1. Main technical parameters of metal rotor flowmeter

(1) Basic measurement range: Water (20 ℃) 2.5-150000L/h Air (20 ℃ key type, 0.1013MPa) 0.07-4000Nm3/h Range ratio: 10:1 Accuracy

1.5/2.5 Working pressure: ≤ 6.4MPa Working temperature: -40~350 ℃ (fluoroplastic lining -10~80 ℃) Environmental temperature: -20~80 ℃ Medium viscosity: DN15 ≤ 5mPa. SDN25~DN150 ≤ 250mPa. S Pipe body material: 1Cr18Ni9Ti, 316L, lined with PTEF, etc. Process connection: flange, or according to the steam provided by the user. Head: flange, DN15/PN1.6， Or as provided by the user

(2) Remote transmission device ① GD 5W1-1 angular displacement transmitter basic error

1.5% F.S output signal: 4-20mA load impedance: 350 Ω power supply voltage: 24VDC ambient temperature: -30~80 ℃ outlet: M20 × 1.5 explosion-proof mark: ExibIICT4 ② GD E-HD transmitter power supply influence:<0.1% (excluding digital resolution [70 μ A]) load influence:<0.1% (excluding digital resolution [70 μ A]) current loss: 4-21.6mA, 0% relative to the measured value load impedance: 0-800 Ω working voltage: 12.8-30VCD two-wire Rext [K Ω]=(Power supply [V] -12.7)/22mA output signal: 4-20mA ambient temperature: -25~80 ℃ outlet: M20 × 1.5 explosion-proof mark: ExibIICT6 measurement range: water (20 ℃) 2.5-150000L/h, air (20 ℃, 0.1013MPa) 0.07-4000Nm3/h range ratio: 10:1 accuracy

1.5/2.5 Working pressure: ≤ 6.4MPa Working temperature: -40~350 ℃ (fluoroplastic lining -10~80 ℃) Environmental temperature: -20~80 ℃ Medium viscosity: DN15 ≤ 5mPa. S, DN25~DN150 ≤ 250mPa. S Pipe body material: 1Cr18Ni9Ti, 316L, lined with PTEF, etc. Process connection: flange, or according to the users preferred steam sleeve: flange, DN15/PN1.6， Or according to the speci

fications provided by the user for the LZ series metal rotor flowmeter: through diameter (mm) flow range pressure loss kPa water L/h * air M3/h * water air conventional type anti-corrosion conventional type, Anti corrosion type 15 2.5~25---0.07~0.7 6.5 7.1 4.0~40 2.5~25 0.11~1.1 6.5 7.2 6.3~63 4.0~40 0.18~1.8 6.6 7.3 10~100 6.3~63 0.28~2.8 6.6 7.5 16~160 10~100 0.40~4.0 6.8 8.0 25~250 16~160 0.7~7.0 7.2 10.8 40~400 25~250 1.0~10 8.6 10.0 63~630 40~400 1.6~16.0 11.1 14.0 25 100~1000 63~630 3~30 7.0 7.7 160~1600 100~1000 4.5~45 8.0 8.8 250~2500 160~1600 7~70 10.8 12.0 400~4000 250~2500 11~110 15.8 19.0 40 500~5000---12 ～ 120 10.8 9.8 600 ～ 6000---16 ～ 160 12.6 16.5 50 630 ～ 6300 400 ～ 4000 18 ～ 180 8.1 8.6 1000 ～ 10000 630 ～ 6300 25 ～ 250 11.0 10.4 1600 ～ 16000 1000 ～ 10000 40 ～ 400 17 .0 15.5 80 2500～25000 1600～16000 60～600 8.1 12.9 4000～40000 2500～25000 80～800 9.5 18.5 100 6300～63000 4000～40000 100～1000 15.0 19.2 150 20000～100000 --- 600～3000 19.2 20.3

2. May I ask fellow citizens: What does G represent in the specifications and models of flow meters? Does it mean working conditions, G25 table ..

It is estimated that G represents the meaning of pipeline, but it still depends on the manufacturers instructions, Qi Hui. G25 may represent DN25, G100 may represent DN100, but the specific definition may vary for each manufacturer. When the reference medium is water, the flow rate of DN25 is usually between 1 and 10 cubic meters per hour, while the flow rate of DN100 is usually between 2 and 200 cubic meters per hour. However, if it is a gas, the situation will be different because the density of the gas varies greatly, so the measurement range will also vary greatly. It should be noted tha

What does T/HT mean in a water flow meter?

1. Main technical parameters of metal rotor flowmeter

2. May I ask fellow citizens: What does G represent in the specifications and models of flow meters? Does it mean working conditions, G25 table ..

『SILVER Official Website SERVICE』